Nc1340 Fitting And Turning Signed Off NCV Level 4 — Memo

November 2024 — NCV Level 4 — Nc1340 Fitting And Turning Signed Off

NCV Level 4 2024 NCV Engineering

↓ Download PDF 📄 199.2 KB

Preparing document

📋 Document Analysis

📄 5 pages 📝 29 items found

See full analysis

Questions — A Preview of What to Expect in the Document

This section provides a quick preview of questions from the document. It may not display every question or the complete wording of each one. For the full content, including diagrams, tables and other information, view the original PDF above.

Q1— Section header —

1.1.1False

1.1.2True

1.1.3False

1.1.4True

1.1.5

1.2.1During the reporting process based on the workshop policy, it is recommended that all defects and defective equipment be reported as and when the defects occur. Vane compressor Rotary screw compressor

1.4and then discharged into an inter cooler. At the inter cooler, the pressurised air is cooled down before entering the high

Q2— Section header —

2.1refers to a measurement of force per unit area that acts on an object in the fluid on a closed containers surface. The ISO unit for ressure is Pascal (Pa\. Volumetric flow rate refers to the volume of fluid that is passing through a

2.2

2.4.1Linear actuator

2.4.2Filter strainer

2.4.3Flow valve

2.4.4Exhaust valve

2.4.5

2.5.320

Q3— Section header —

3.1Place a piece of paper between the workpiece and the magnetic base to prevent the workpiece or magnetic base surface from damage. (2\

3.2Once one is satisfied that every safety aspect has been taken into consideration and applied, one may start the machine. Stand aside and let the machine run for approximately five minutes to allow

3.3.110

Q4— Section header —

4.1Make sure that the centre lathe is anchored to the floor. Inspect power supply cables and the emergency stop to ensure that they are in good working condition. Inspect guards to make sure that they are in position and in good working

4.2The operator must select the cutting tool based on the requirements of the job. The selected cutter must then be clamped with bolts into the bracket in the tool post. It must protrude approximately 10 mm from the tool post so that it has the

Q5— Section header —

5.1Let the machine and spindle come to a complete stop before opening the door. Ensure that the work piece and tools are secured properly. Do not use tools for which one has not been trained to use. Carefully inspect tools every time before they are them.

5.2Use paint brush/hook wire to clean off stray chips/shavings and debris. (2 (4\

5.3The worn tip is loosened by means of an Allen key and then turn around and fitted into the holder. ufficient spare inserts for all the tools. Correct size of Allen keys available for the tools being used.

5.7

Mark Allocation

Sections20 + 20 + 10 + 24 + 26 = 100 marks

Paper information

TitleMemo

SubjectNc1340 Fitting And Turning Signed Off

LevelNCV Level 4

Document typeNCV Engineering

Year2024

MonthNovember

Pages5

Downloads4

Examination context

Decade2020s

Years ago2y

SeasonSpring (SH)

Start dayFriday

Exam periodNovember 2024

Days since exam707

About Nc1340 Fitting And Turning Signed Off examination preparation

This TVET examination resource can be used as part of a structured revision programme. Past papers are most useful when learners attempt questions independently, work within a realistic time limit, and review their answers afterwards.

How to use this resource for revision

A TVET past examination paper is most useful when it is treated as an active revision exercise. Try the questions yourself before checking the corresponding memorandum. Where you make an error, identify the reason — was it a knowledge gap, a calculation mistake, an interpretation issue, or an examination technique problem?

For stronger examination practice, complete the paper without unnecessary interruptions and keep track of the questions that take the most time. Afterwards, review the memorandum and separate knowledge gaps from mistakes caused by interpretation, calculation, structure, or examination technique.

understanding question requirements

applying subject knowledge

working under time constraints

checking answers

identifying revision priorities

A practical revision approach

Start by completing the resource without looking at the memorandum. Review incorrect and incomplete answers afterwards and make a short revision list based on the areas that caused difficulty.

File details

File size199.2 KB

Pages5

Archived on8 September 2026

File age45d

ContributorFreeMode

FingerprintC68A1DB73149

Questions and learner discussion

No questions or discussions have been posted yet.